Learning Center

Everything you need to know about caring for, assembling and planning your Catio Haus walk-in catio.

Materials & Care

Alumawood Care & Maintenance

Your Catio Haus frame has a factory-baked finish and your enclosure uses 4-track FlexiGlaze® vinyl over continuous TuffScreen. A little routine cleaning keeps everything looking its best.

Cleaning the Alumawood frame

Airborne pollutants, such as car exhaust and nearby industry, can leave an acidic film on any baked enamel finish. Remove it with periodic cleaning: mix a few teaspoons of dishwashing liquid into a bucket or hose sprayer, apply to all exposed surfaces, then rinse thoroughly with clean water.

Removing mildew

Black spots on protected surfaces, such as under the roof edge or in shaded corners, may be mildew. Mix 1/3 cup laundry detergent, 2/3 cup tri-sodium phosphate and 1 quart of 5% household bleach. Apply with a sponge or soft cloth, then rinse well. Wear protective gloves and avoid skin contact. Stronger mixtures can damage the finish.

Keep cats indoors while cleaning, and rinse every surface fully before letting them back in.

Caring for FlexiGlaze® vinyl panels

  • Rinse dust off first so grit doesn't scratch the vinyl.
  • Wash with mild soap and lukewarm water using a soft microfiber cloth.
  • Never use ammonia, glass cleaners, solvents or paper towels on vinyl.
  • Wipe the 4-track channels and keep them free of debris so panels slide smoothly.

Caring for TuffScreen

  • Brush off fur and debris with a soft brush or vacuum attachment.
  • Spot-clean with mild soapy water and rinse with a gentle hose spray.
  • Inspect seasonally for any areas your cat has worked at.

What to avoid

  • Abrasive pads, scouring powders or wire brushes.
  • Solvent-type cleaners or paint removers — they can soften or remove the baked finish.
  • Pressure washers at close range.

Materials & Care

Alumawood vs. Wood Catios

Alumawood has the look of real wood grain with the strength and longevity of aluminum — a better fit for an outdoor space your cat lives in every day.

Why Alumawood wins for catios

  • Will not rot, warp, split or splinter.
  • Resists mold, mildew and termites.
  • The finish is baked into the material, so it won't peel like paint.
  • No stains, sealers or pressure-treated lumber for cats to lick or chew.
  • Little ongoing care beyond occasional washing.
  • Costs less over time once you factor in wood upkeep.
  • Helps protect forests by using aluminum instead of lumber.

Finishes

Every Catio Haus frame is available in White, Espresso or Ebony Alumawood with an embossed wood-grain texture. The 4-track window channels are smooth aluminum, so they look slightly different from the frame — see the color samples on each model.

DIY & Assembly

Tools Needed for Assembly

Your kit includes the frame, cover, vinyl window system, TuffScreen and structural hardware. The tools below are the ordinary ones most homes already own — a drill, a level, a tape measure. If you've hung a shelf or assembled flat-pack furniture, you're already most of the way there, and anything missing is an inexpensive trip to any hardware store.

Tool checklist

  • Cordless drill / impact driver with assorted bits
  • Hammer drill with a 3/8″ masonry bit (for anchoring into concrete)
  • 3/16″ × 5-½″ Tapcon concrete screws — you supply these, they're not included in the kit
  • Chop saw or jigsaw with a fine-toothed metal-cutting blade
  • 4-foot level and a torpedo level
  • 25-foot tape measure
  • Chalk line and heavy-duty carpenter's pencil
  • Step ladders (two recommended)
  • Caulking gun with exterior sealant
  • Rubber mallet
  • Safety glasses, work gloves and hearing protection

Helpful tips

  • Plan on at least two people for raising the frame and setting the cover.
  • Parts include a small overproduction margin, so some trimming to final size is expected.
  • Follow the interactive 3D build instructions step by step.

Engineering & Site Prep

Engineering, Permits & HOA

Rules for outdoor structures vary by city and HOA. Check with your local building department and HOA before you build.

Do I need a permit?

Some cities don't require a permit for smaller structures, while others do. Your building department can tell you what applies to a wall-attached walk-in catio at your address.

What departments usually ask for

  • A site plan: a simple drawing of your yard, the catio and its measurements.
  • Product engineering for the frame and cover.
  • Attachment details showing how the catio connects to your house wall.

Wind and snow loads

Standard kits are engineered for Wind Speed B100 and Snow Load 0. During order review we email you to confirm your local wind and snow load requirement. Some areas may need added steel reinforcement, which can affect pricing.

HOA submissions

Each Catio Haus model comes with clear drawings and specs you can hand to your HOA architectural committee, along with your chosen finish color.

Engineering & Site Prep

Ground Slope & Foundation Guide

Your catio sits on a firm, level surface and attaches to a house wall — never to fascia or the roof. The larger dimension runs along the wall.

Suitable ground

  • Existing concrete slab (ideal).
  • Well-compacted, stable pavers.
  • Structurally framed surfaces only after review with us.

How to check your ground slope

  • Set a straight 4-foot board on the ground, running away from the house wall.
  • Place a level on the board and lift the low end until the bubble is centered.
  • Measure the gap between the board and the ground in inches.
  • Repeat along the wall and at the outer corners, then share the numbers with us.

Why it matters

Most slabs slope gently away from the house for drainage — that's normal. Knowing the slope lets us confirm your model is a good fit and that the doors and vinyl panels will operate smoothly.

Questions?

Email hello@catiohaus.com or call us.